grabcad
4 Step Stair Stringer
Part for Deck Stairs
4 step stringer 3D Models
785 resultsSponsored
grabcad
prusaprinters
Functional Rubiks Cube. No supports!
This model is a fully functional cube that does not require support material to print.T...
prusaprinters
Simple eyeglasses or sunglasses holder- 2, 3, or 4 pairs!
I made this model for use in our bathroom to hold our eyeglasses. Could also be used fo...
thingiverse
Screen Door Handle
Designed this handle for a sliding door screen as the original is hard to use. I pri...
thingiverse
Trash Can Lift Hinge
This is the part of a trash can hinge where the step mechanism attaches and lifts the l...
thingiverse
Roomba ramp - Wider and stronger ramp for vacuum robots
In this remix i stretched the ramp so i only needed 4 pieces to fit my door width, also...
SPONSORED
⚽ Toy Soccer Cup — flick football, free
Free browser game · Real multiplayer · No install
thingiverse
Inverted bicycle stands
These are inverted bicycle handlebar stands. Designed to throw into the back of the car...
thingiverse
Heavy Hydra air defense turret with posable radar
So, this model originally had a few problems, in my opinion. The embedded radar didn't ...
thingiverse
03-04 Cobra Bumper Fog Light Adapter
Designed to adapter 4" LED Jeep fog lights to the 2003-2004 SVT Cobra bumper allowing f...
thingiverse
Lancia Delta HF Integrale - Trunk Cover Repair KIT
Improved version for Lancia Delta I (831ab0) trunk cover parts. This parts are stronger...
prusaprinters
Repurpose CD or DVD wire rack as a wall shelf with 3D printed wall mount
We had an old CD wire rack lying around, what nobody wanted. So I repurposed or upcycle...
thingiverse
CR-10 Stronger Squash Foot
I liked the idea of Dr. Boo's squash foot, but I did not like the overhang between the ...
thingiverse
LiIon 18650 Power bank for FLYSKY FS-i6S or other devices
### Power Bank for FS-i6S or other devices. #### Need for assembly: -Two 18650 Li...
thingiverse
Skadis Vesa Mount More Pegs
I liked this design but I was worried that 4 pegs would not be strong enough. Made this...
prusaprinters
4 Way Splitter for Magnetic Hose Coupler
4 way hose breakout system for magnetic coupler design by furfoxsake on thingiverseRequ...
thingiverse
KitchenAid KHB1231HT Hand Blender - Neck holder replacement
The stock one split in half after using this device for less than 20 times. I couldn't ...
thingiverse
Magnetic/Suction Cup Breadboard Mount
A magnetic/suction cup mount for 1/2 (half-sized) breadboards. For whiteboards and stra...
cgtrader
OpenRC Truggy Tire Experimental Free 3D print model
This is a experimental tire for the OpenRC Truggy. Expect this thing to change! It is...
prusaprinters
Trash Can Lift Hinge
This is the part of a trash can hinge where the step mechanism attaches and lifts the l...
thingiverse
Magnetic Jaws for Master Force 4 Vise
I loved Evan and Katelyn's vise jaws, but they didn't fit my vise, a Master Force #4. T...
cults3d
FTC Robot
In this updated FTC Robot - Updated instructions and parts list - Easier way to build t...
thingiverse
FTC Robot
In this updated FTC Robot - Updated instructions and parts list - Easier way to build...
pinshape
OpenRC Truggy Tire (Experimental)
This is a experimental tire for the OpenRC Truggy. Expect this thing to change! It is p...
thingiverse
OpenRC Truggy Tire (Experimental)
This is a experimental tire for the OpenRC Truggy. Expect this thing to change! It ...
cults3d
LM2596 and LM2596S Buck converter tool-less snap-fit enclosure - Ender, CR-10, 2020
A tool-less, snap-fit enclosure for your LM2596 buck/step-down converter that should sn...
thingiverse
Chainmail - European Rivet Design
Update: I learned that for proper chainmail, each riveted ring holds 4 non-riveted, sim...
prusaprinters
Sand Spike Camera Mount Insert - 1.5-in & 2-in with 1/4-20 Threads
This is simple 1/4-20 camera mount designed to fit inside most PVC sand spikes with an ...
thingiverse
Ryobi Track Saw Track Accessories
Ryobi messed up by not including an accessory track on the guide rail. This attempts t...
thingiverse
Creality CR-6 SE Replacement Spool Holder
I'm working on building an upgraded spool support for the CR-6 SE with bearings, but as...
thingiverse
Dog Bone with Steel Core
This is my take on the Dog Bone from the Tarmo 4 project. The original had a stronger ...
Sponsored