cults3d
Rotor Riot CL1 Accessories
30 degree Hero8 mount 30 degree Session mount Front bumper Arm guards Long range antenn...
cl1 rotor riot 3D Models
74 results
cults3d
thingiverse
Rotor Riot CL1 Accessories
- 30 degree Hero8 mount - 30 degree Session mount - Front bumper - Arm guards - Lon...
thingiverse
Rotor Riot CL1 Drone
Rotor Riot CL1 Drone
prusaprinters
Rotor Riot CL1 GoPro Mount
This works with the Rotor Riot CL1 frame, and would likely work with others. You will n...
thingiverse
Rotor Riot CL1 GoPro Mount
This works with the Rotor Riot CL1 frame, and would likely work with others. You will n...
thingiverse
Rotor Riot CL1 Frame Accessories
Official Rotor Riot Accessories =========== These are the official accessory STLs f...
thingiverse
Rotor Riot CL1 GoPro Mount
Standard GoPro Mount that will screw to the front four screws of the Rotor Riot CL1 cha...
thingiverse
Rotor Riot CL1 Session mount
I cut the top off the wedge mount by blinkFPV and put the GoPro Session Protector by Ai...
thingiverse
Rotor Riot CL1-SMA Mount
I made this for the CL1 frame with 20MM standoffs. itll fit the standard 30MM standoffs...
cults3d
ROTOR RIOT CL1 VS_CAPACITOR MOUNT
CAPACITOR MOUNT FOR FPV FRAME ROTOR RIOT CL1 VS
thingiverse
Rotor Riot CL1 GP8 Skull mount
skull mount for gopro 8. rotor riot cl1 frame
thingiverse
Rotor Riot CL1 tracer antenna mounts
TBS Tracer antenna mounts for the Rotor Riot CL1, with sma mount with the mounting holes.
thingiverse
Rotor Riot CL1 hero8 polarpro mount
a mount for the hero8 with polarpro filers on a rotor riot CL1
thingiverse
Rotor Riot CL1 SMA Mount v2
this is my second sma mount for the CL1 rotor riot frame. the first one is ok, the ante...
thingiverse
rotor riot cl1 immortal t mount
here I designed a sturdy option for mounting an immortal t antenna on the rotor riot cl...
thingiverse
Rotor Riot CL1 Polariod Cube Mount
Got tired of using straps on this frame so I decided to remix my [Armattan Marmotte mou...
thingiverse
Gopro mount for rotor riot cl1
This is a gopro mounting accessory for the rotor riot cl1 frame. I have tested printing...
cults3d
ROTOR RIOT CL1 VS_ANTENNA VTX MOUNT_V1
ANTENNA MOUNT FOR FPV FRAME ROTOR RIOT CL1 VS V1
cults3d
ROTOR RIOT CL1 VS_ANTENNA VTX MOUNT_V2
ANTENNA MOUNT FOR FPV FRAME ROTOR RIOT CL1 VS V2
cults3d
ROTOR RIOT CL1 VS_GOPRO BASE MOUNT
GOPRO BASE MOUNT FOR FPV FRAME ROTOR RIOT CL1 VS
myminifactory
Rotor Riot CL1 GoPro Mount 30 Degrees
This is a 30 degree GoPro Session mount for the Rotor Riot CL1. Print on its side for b...
prusaprinters
20mm Mods for Rotor Riot CL1 Frame
I recently built a quad based on the Rotor Riot CL1 frame. I wanted to have a low profi...
thingiverse
Rotor Riot CL1 GoPro Mount 30 Degrees
This is a 30 degree GoPro Session mount for the Rotor Riot CL1. Print on its side for ...
thingiverse
GoPro Mount for Rotor Riot CL1 Frame
GoPro mount for Rotor Riot CL1 frame. Printed in TPU at .2mm Layer. You may want to t...
thingiverse
Rotor Riot CL1 RX Mount 5mm/3mm
you may need to play with scale since when it cools it likes to shrink. id say 103-105%...
thingiverse
Rotor Riot CL1 SMA Mount 20mm/30mm
ok I made another one at 30mm height for the standoffs the frame ships with. if you wan...
thingiverse
20mm Mods for Rotor Riot CL1 Frame
I recently built a quad based on the Rotor Riot CL1 frame. I wanted to have a low profi...
thingiverse
Rotor Riot CL1 Arm Bumper / Soft Mount
Arm Bumber for the CL1 Frame which also soft mount the motors. Print 2 regular and 2 mi...
thingiverse
Rotor Riot CL1 SMA and GPS Mount
Rotor Riot CL1 SMA pigtail and GPS mount. GPS size holds a roughly 18x18mm GPS puck. I ...
thingiverse
Rotor Riot CL1 VTX and RX Mount
This is a mount I made to hold my VTX and RX transmitter on my quadcopter. This is des...