thingiverse
Pipe Cutting Guide
This is a clamp-on guide for cutting 2-inch PVC pipe (should work for ABS as well). It ...
pipe cutting guide 3D Models
90 resultsSponsored
thingiverse
thingiverse
Pipe Cutting Guide SCAD
This is a quick and dirty SCAD that is very similar to the Pipe Cutting Guide that was ...
thingiverse
carbon pipe(OD5mm) cutting guide
It is used to put the saw in the groove.
grabcad
Pipe Cutting 45 Degree Guide 3D-Printed
I wished to weld 2 unusual size pipes together with one welded on at a 45 degree angle....
thingiverse
Shaft fixture
Shaft fixture - Use for cutting with a cutter or a saw. - Shaft and pipe can be fixed...
thingiverse
8 GHz Chaparral feed
8 GHz Chaparral section, septum polarizer and copper pipe cutting guide to make a feed ...
SPONSORED
🤖 Commercial humanoid robots under $10K by 2027?
The future of AI is tradeable. Predict tech breakthroughs.
thingiverse
Customizable Cylinder
This is a customizable cylinder derived from "Pipe Cutting Guide SCAD" by dr00bie that ...
prusaprinters
50mm PVC Tube cutting guide
This is a cutting guide I created to fit around a common 50mm PVC drain pipe. This all...
cults3d
AOI Smith 5" Concentric Tube cutting jig
Compatible with Direct Venting Systems for AO Smith / Takagi 110C, 310C and 510C Gas Ta...
thingiverse
Simple tool for 1/2 Inch PVC pipe cutting
Simple tool for PVC pipe cutting with saw blade, makes perpendicular cuts very easy. Fi...
cults3d
Simple tool for 1/2 Inch PVC pipe cutting
Simple tool for PVC pipe cutting with saw blade, makes perpendicular cuts very easy. Fi...
thingiverse
Cutting guide for welding T joint with two tubes
This is designed to slide over a pipe with an outer diameter of 2.44 inches (62mm). Us...
thingiverse
Tile hole cutting tool guide
Hi... this tool is for hole guide cuting in tiles.. wood panels etc. features: Pipe...
thingiverse
Parametric Pipe Cutting Jig
This is a parametric pipe cutting jig. You can customize the pipe diameter, the blade t...
thingiverse
CTC Dual Filament Guide
CTC Filament Guide fits directly onto a CTC dual 3D printer fits with NO modifications ...
cults3d
12mm Bullet pixel drill guide for 1/2 inch PVC pipe
This is a 3 inch spacing drill guide for 1/2 PVC pipe to be used to install RGB pixel l...
thingiverse
12mm Pixel RGB Drill guide with 2 inch spacing for 1/2 inch PVC
This is a drill guide for 1/2 PVC pipe to be used to install RGB pixel lights for a hou...
thingiverse
12mm Bullet pixel drill guide for 1/2 inch PVC pipe
This is a 3 inch spacing drill guide for 1/2 PVC pipe to be used to install RGB pixel l...
thingiverse
Kawasaki Driveshaft Tube Mod Centering Rings
Centering rings to center the 1" schedule 40 pvc pipe in the oem driveshaft tube when f...
cults3d
6mm Air Line Trimming Square
This is a simple cutting template for 6mm tubing - in my case, the hoses for Range Rove...
thingiverse
6mm Air Line Trimming Square
This is a simple cutting template for 6mm tubing - in my case, the hoses for Range Rove...
thingiverse
PVC Shop hardware organizer with 3D printed inserts
I was looking for a shop storage solution to store nuts and bolts in my shop. I came ac...
thingiverse
Creality Ender 3 filament guide with PTFE tube
I have tried, for my Ender 3, different filament guides for the extruder stepper motor,...
cults3d
Ikea Lack 3D Printer Enclosure
Minimalistic enclosure using 50cm x 50cm x 2mm hobby glass (polystyrene) panes. Side a...
thingiverse
Ikea Lack 3D Printer Enclosure
Minimalistic enclosure using 50cm x 50cm x 2mm hobby glass (polystyrene) panes. Side...
thingiverse
Ver2 : Anti-Vibration Feet for Makerbot / Wanhao / Ultimaker etc
My new foot at http://www.thingiverse.com/thing:1367244 works a lot better than this T...
thingiverse
timing-belt-fix
It is a simple square pipe with bigger opening at one side. It is meanth to easily mou...
thingiverse
Geeetech IKEA Lack accessories
I wanted to house my Geeetech i3 printer in a friendly environment, and make it to look...
thingiverse
HOWARD DGA-5 "IKE" VERSION 2.2 - PRINT TEST PARTS
Important note: It's only test parts! PLA: Canopy and a front part of the fuselage sho...
thingiverse
Eight Filament Reel Holder from PVC Pipe
I needed a way to quickly and easily keep my filament ready for printing; versus taking...
Sponsored
Sponsored